Screed or Slab Heating Kits

Availability: In Stock

Product Name Price Qty
20mm x 7.5m Roll of galvanized fixing rail
$AUD 20.90
Screed/Slab Heat Kit - 180W - 10m - 0.8A
$AUD 114.40
Screed/Slab Heat Kit - 360W - 20m - 1.5A
$AUD 170.50
Screed/Slab Heat Kit - 540W - 30m - 2.3A
$AUD 207.90
Screed/Slab Heat Kit - 765W - 42.5m - 3.2A
$AUD 266.20
Screed/Slab Heat kit - 1080W - 60m - 4.5A
$AUD 352.00
Screed/Slab Heat Kit - 1440W - 80m - 6.0A
$AUD 451.00
Screed/Slab Heat Kit - 1800W - 100m - 7.5A
$AUD 544.50
Screed/Slab Heat Kit - 2160W - 120m - 9.0A
$AUD 634.70
Screed/Slab Heat Kit - 2520W - 140m - 10.5A
$AUD 737.00
Screed/Slab Heat Kit - 2790W - 155m - 11.6A
$AUD 808.50

ATTENTION!

Thermostats are not included in the kit as there are various options available. Visit the THERMOSTAT page after you have added your kit to the cart or look at the OUR RELATED PRODUCTS tab below and make your selection there

Overview

Quick Overview

Slab and Screed Heating Kits

rug heater
(One free rug heater per order)

FREE SHIPPING Australia Wide when you buy online


10 year warrantyThe Coldbuster screed/slab heater is a bi-directional, single ended 6mm cable and is rated at 14W/m and is supplied as a cable on a roll. To achieve a specific wattage per square meter, secure the cable at the spacing centres recommended for your heating design. Heaters have 2.4m long leads that can be connected to a programmable or manual thermostat control. A range of 8 standard lengths or combination of these lengths caters for all room sizes e.g. from small bathrooms to large halls.

Description

Details

rug heater
(One free rug heater per order)

FREE SHIPPING Australia Wide when you buy online

Thermostatic comfort control

Complete comfort control is easily achieved with the addition of optional manual or programmable thermostats available through Coldbuster.

Automated operation enhances the energy efficiency of the Coldbuster cable heating system. Programs can be set to regulate comfort levels via floor or room air temperature, up to 4 cycles per day, accommodating different weekday and weekend routines.

Unobtrusive and safe

Coldbuster in-screed and in-slab cable can be installed directly to concrete reinforcing or secured to a metal ‘fixing rail’ for in-screed application. Coldbuster in-screed cable is suitable for the majority of floor finishes. The heater is waterproof, fully earthed and needs to be connected to a RCD circuit at the time of installation to ensure full protection against fire and shock hazards.

Multi application heating system

Following the recommended layout provided, unroll the heater strip and fix to mesh or rails. Care must be taken to never cross over elements.

The various ways to fix the cable in position include;

In-Slab application - The cable is tied to the reinforcing mesh
In-Screed application -Clip cables on to the metal fixing rails, which are nailed to the slab.
In-Screed on waterproofing, tie cable to reinforcing mesh or secure cable with duct tape. (Metal fixing rails can be used if glued onto the waterproofing)

 

slab heating installation        

Coldbuster tile heating is classified as an appliance and can be installed by any competent person. The heater must be connected to a RCD (safety switch) protected circuit by an electrician. All wiring must conform to AS/NZS 3000:2000 and local wiring regulations.

Service & support

Coldbuster provide a free design service and planning advice for your complete room heater layout. We are available to answer your questions relating to electrical preparation or installation of your floor heating system. If you prefer to leave the installation to a floor heating contractor, a professional design & installation service is available across Australia.

Robust Screed and Slab heating cable 

Coldbuster screed heating cable comes in 8 different lengths. A combination of these lengths caters for all room sizes e.g. from small bathrooms to large halls and acts as the primary or secondary heating source.The screed heating cable features;

  • Bi-directional, single ended 6mm cable is rated at 14W/m and is supplied as a cable on a roll.
  • Factory terminated 2.4 metre 'cold tail' power lead on heater
  • Installation guideline and personalised floorplan layout
  • Technical & installation support (telephonic)
  • Can be supplied as a kit including installation monitor, programmable thermostat and metal fixing rail
Additional Info

Additional Information

Heater Size From 10m to 155m Cable Rolls
Area From (m2) 1.2
Area To (m2) 27.9
Watts No
Amps No
Video
Product Downloads
Our Related Products

Based on your selection, you may be interested in the following items: